ISO QMS Certified
"Our Science ... Your Success"

3D Print Infiltrants

  • Home
  • 3D Print Infiltrants

3D Print Infiltrants

Permabond 3D Print Infiltrants are low odor alkoxyethyl cyanoacrylates designed to seal, strengthen, and brighten 3D printed models produced via granular 3D printing methods.

Several grades of these low odor cyanoacrylates are available to suit individual needs.  All of them can be applied either as an “on the spot” coating or in a dip bath.  All are single component, moisture cure, low odor, solvent free, clear, colorless, and cure to a tack free finish.  They are suitable for white and colored parts.

Permabond 3D30 has an ultra fast cure and provides a high gloss crystal clear surface with brilliant color vibrancy.

Permabond 3D10 has a fast set and provides a shiny surface with brilliant color vibrancy.  The low viscosity provides good penetration for higher strength.

Permabond 3D90 is ultra low viscosity and has a delayed set for maximum penetration for highest strength.  It is ideal for light colors.

The technical data sheet provides more information.

3D Print Infiltrants – Directions for Use

Before use:
  1. Refer to SDS for safe handling.
  2. Wear nitrile gloves, safety glasses and protective
  3. Work in a ventilated area.
  4. Prepare surface with a non-stick paper such as freezer paper, PTFE sheet, wax paper etc…
  5. Determine which method below best suits your part.
Drizzle Method – Ideal for small or delicate parts.
  • Place part on a protective sheet in a catch
  • Apply directly from small size bottle or use spout with larger
  • Either apply to the entire part – turning the part as you drizzle, or apply only to very fragile sections then follow with the Dip Method
  • Allow the part to cure – times vary with product used. Most parts can be handled in less than 15 minutes.
Dip Method
  • Remove excess
  • Pour Permabond 3D Infiltrant into a clean metal, glass, polypropylene or polyethylene container. Ensure the quantity is sufficient to allow complete submersion of the
  • Submerge part slowly so as not to splash the
  • Keep the part submerged as long as you see bubbles rising. If there are no bubbles, remove part after 10 seconds.
  • Transfer part hand to hand over the bath. This will allow excess to drip back into the container and ensure the part will not stick to your
  • Wipe any excess infiltrant with paper towels. (Wet towels with water prior to )
  • If excess infiltrant pools under the part – wipe it away with paper
  • Allow the part to cure – times vary with product used.  Most parts can be handled in less than 15 minutes.
  • Carefully pour any unused infiltrant back into the bottle and cap tightly.

3D Print Infiltrants

Contact us for more information

Product Brochure (PDF)

Contact Us

 Your information is always kept private

Products

Recent Blogs

03Apr
Permabond’s Structural Epoxy Adhesives for Stainless Steel

Permabond launches high strength structural adhesives for tarnish free bonding of stainless steel. Available in convenient 1:1 dual cartridges, once mixed via static mixer nozzle, these adhesives achieve full cure at room temperature (...

Read more
18Mar
How To Bond Plastic To Metal

There are metal adhesives and plastic adhesives but what to do when you want to bond plastic to metal? There are metal adhesives that bond some plastics and plastic adhesives that bond some metals. The specific substrates, as well as the surf...

Read more
13Mar
Permabond at JEC World Paris

Day 2 of JEC World Paris. Permabond is in the UK pavilion in hall 6, stand S50, and is busy helping to find bonding solutions for a diverse range of composites applications (honeycomb panels, carbon fibre automotive components, marine app...

Read more
04Mar
Permabond 2K Primer and Adhesion Promoter

Permabond 2K Primer is a dual purpose product, which indicates whether or not sufficient surface preparation has been carried out and contains an adhesion promoter to increase bond strength.  It is ideal for preparing metal, glass, plastic, ...

Read more
13Feb
Join Permabond at Design 2 Part in Grapevine TX

Join Permabond March 13th and 14th at the Design-2-Part Manufacturing Show at the Gaylord Texan Convention Center. Register here and visit Permabond in booth number  223.  

Read more
05Feb
Permabond returns to Southern Manufacturing & Electronics, Farnborough

Off to a busy start at Southern Manufacturing & Electronics! Visit us on A165 right by the entrance to find out how to maximise your adhesive's performance with Permabond 2K Primer, bond polypropylene/polyethylene WITHOUT surface prep...

Read more
21Jan
Metal Bonding Acrylic Adhesives

Metal Bonding Acrylic Adhesives Epoxies, Cyanoacrylates, and several other technologies provide excellent adhesion to metals.  Acrylic metal bonding adhesives are often chosen not only for the strong bonds to metals but also for the varie...

Read more
08Jan
Join Permabond at Expo Manufactura

Join Permabond® Engineering Adhesives at Expo Manufactura February 5th through the 7th from 1:00 p.m. to 8:00 p.m. at Cintermex in Monterrey, N.L. Mexico Register here and visit Permabond in booth number 929! Únase a Permabond® Adhes...

Read more
10Dec
Blue Center Innovation Technologies

Blue Center Innovation Technologies – Permabond’s new state of the art development, technical service & QC laboratories Misinto, Italy - 28th November 2018 Permabond has a history of developing and manufacturing engineering ...

Read more
24Nov
Industrial adhesives Vs Consumer adhesives

What are industrial adhesives? How do they differ from consumer adhesives?  Strictly speaking, industrial adhesives are adhesives that are labeled for industrial use.  Various local and global bodies require industrial adhesives to include...

Read more
23Oct
5-minute epoxy – more than the name implies

Recently I received a call for a 5-minute epoxy. In general terms, 5-minute epoxy is used to refer to two-component epoxy that start to set up in around 5 minutes.  But they are not all alike.  Epoxies can vary in viscosity, mix ratio, colo...

Read more
16Oct
Pipe Size Diameter and Thread Sealant Use

Permabond LH050 general purpose anaerobic pipe sealant is for use on metal pipe.   Permabond LH050  is classified by Underwriters Laboratories Inc.® for use in devices handling gasoline, petroleum oils, and natural gas (pressure not over ...

Read more
01Oct
Plastic Threadlockers

Threadlockers fill the space between the threads which prevents vibration loosening.    Anaerobic threadlockers are used for metal fasteners; they should not be used on plastics as metal ions are required to cure the material, and they can...

Read more
16Sep
Industrial Adhesives for Dissimilar Substrates

Bonding Dissimilar Substrates It goes without saying that if you are bonding plastics use a plastic adhesive and if your bonding metal, an adhesive for metal.  It gets more complicated when you want to choose industrial adhesives to join di...

Read more
11Sep
Efficient scale up – Adhesive processes

One of the questions our tech team asks engineers seeking an adhesive recommendation is “How many assemblies will you be manufacturing?”  Although from a business perspective this is nice information to have; it is critical information t...

Read more