ISO QMS Certified
"Our Science ... Your Success"

Permabond 792

  • Home
  • Permabond 792

PERMABOND 792 Surface Insensitive Cyanoacrylate

PERMABOND® 792 is a low viscosity, surface insensitive adhesive that will rapidly bond substrates with acidic surfaces such as wood and plated surfaces. Plastics, metals, ceramics and elastomers are also rapidly bonded. The fast cure minimizes the occurrence of frosting and fogging.
Features and Benefits
  • Extremely fast setting
  • Rapid development of high strength
  • Ease of use – no mixing or heat cure
  • Surface insensitive
  • 100% reactive, no solvents
  • Approved to MIL-A-46050C Type II Class 2 (existing designs) & CID A-A-3097 Type II Class 2 (new designs)

Cyanoacrylate Directions for Use Video

Surface Preparation Directions for Use Video

 

Permabond_TDS_btn

 

Cyanoacrylate adhesives are single component adhesives that polymerize rapidly when pressed into a thin film between parts. The moisture adsorbed on the surface initiates the curing of the adhesive.  Strong bonds are developed extremely fast and on a great variety of materials. These properties make PERMABOND cyanoacrylates the ideal adhesives for high-speed production lines.

permabond 792

permabond 792 cured

 

Surface Preparation prior to bonding with Permabond 792
Surfaces should be clean, dry and grease-free before applying the adhesive. Use a suitable solvent (such as acetone or isopropanol) for the degreasing of surfaces. Some metals such as aluminum, copper and its alloys will benefit from light abrasion with emery cloth (or similar), to remove the oxide layer.

Permabond 792 Directions for Use
1) Apply the adhesive sparingly to one surface.
2) Bring the components together quickly and correctly aligned.
3) Apply sufficient pressure to ensure the adhesive spreads into a thin film.
4) Do not disturb or re-align until sufficient strength is achieved, normally in a few seconds.
5) Any surplus adhesive can be removed with Permabond CA solvent, nitromethane or acetone.
NB:
For difficult or porous surfaces using a Permabond activator is recommended. If bonding polypropylene, polyethylene, PTFE or silicone, prime first with Permabond Polyolefin Primer (POP).

For more information download the Technical Data Sheet

Permabond_TDS_btn

Contact Us

Your information is always kept private

Products

Recent Blogs

21Jul
Permabond MT3836 – Flexible, Fire Retardant and Thermally Conductive Adhesive

Permabond is delighted to announce the introduction of Permabond MT3836 - flexible, fire retardant and thermally conductive adhesive. This two-component hybrid system cures fully at room temperature to form a flexible, thermally conductive m...

Read more
17Jun
Cationic Epoxy/UV Adhesives Cure with UV Light or Heat or Both!

Permabond Europe's new cationic epoxy/uv adhesives cure with UV light or heat or both! Permabond UV7220 (black) and Permabond UV7221 (clear) are epoxy resins that cure when exposed to 365nm UV light, and they can also cure with heat like sta...

Read more
23Mar
Permabond F201 Toughened, flexible, anaerobic sealant

Anaerobic sealants are characteristically very rigid, hard adhesives which work well in compression, torsion and shear but are notoriously brittle and unsuitable in applications where there could be peel or cleavage forces. When bonding dissi...

Read more
03Mar
FDA & EU 10/2011 Compliant Adhesive for Food Contact

PERMABOND® ET5162 is an FDA & EU 10/2011 compliant adhesive. It has been formulated to comply with both FA 175.105 and EU food contact regulations 10/2011. It is a two-part, room temperature curing epoxy adhesive, which combines high pe...

Read more
14Jan
High Temperature Resistant Cyanoacrylate

Permabond introduces new high temperature resistant cyanoacrylate adhesives! PERMABOND® 825 is a low viscosity cyanoacrylate adhesive that provides higher strength at high temperature. This fast-setting cyanoacrylate bonds metals, rubbers, p...

Read more
15Dec
New no odour adhesives for low surface energy plastics

PERMABOND® is delighted to announce the launch of Permabond TA4630 and TA4631, no odour adhesives for low surface energy plastics, especially developed for difficult to bond plastics such as polypropylene, polyethylene and&nb...

Read more
18Jun
Permabond Launches UV639 High Performance Acrylic Bonder

Permabond Launches UV639 High Performance Acrylic Bonder In the world of bonding acrylic (or Perspex®, PLEXIGLASS®, PMMA as it is also known), adhesives used to join this material are often referred to as "acrylic adhesives". This sho...

Read more
28Jun
Permabond Europe Launches TA4207 – No surface preparation!

Permabond Europe Launches TA4207 – A new versatile, high strength adhesive Permabond TA4207 expands our existing range of methyl methacrylate (MMA) adhesives, and is a 2-part, 1:1 mix ratio product, which achieves very high shear strengths...

Read more