ISO QMS Certified
"Our Science ... Your Success"

Permabond 2010

  • Home
  • Permabond 2010

PERMABOND 2010 Thixotropic Cyanoacrylate Adhesive

PERMABOND® 2010 is a thixotropic, fast-setting cyanoacrylate particularly suitable for use on vertical and porous substrates. This material can be used on metals, plastics, elastomers, ceramics, and wood.
Features and Benefits
  • Thixotropic dispensable semi-gel
  • Fast cure
  • Easy to apply and dispense
  • 100% reactive, no solvents
  • Maximum gap filling capability

Cyanoacrylate Directions for Use Video

Surface Preparation Directions for Use Video

 

Permabond_TDS_btn

 

Cyanoacrylate adhesives are single component adhesives that polymerize rapidly when pressed into a thin film between parts. The moisture adsorbed on the surface initiates the curing of the adhesive.  Strong bonds are developed extremely fast and on a great variety of materials. These properties make PERMABOND cyanoacrylates the ideal adhesives for high-speed production lines.

 

permabond 2010 props

Permabond 2010 cured properties

Surface Preparation prior to bonding with Permabond 2010
Surfaces should be clean, dry and grease-free before applying the adhesive. Use a suitable solvent (such as acetone or isopropanol) for the degreasing of surfaces. Some metals such as aluminum, copper and its alloys will benefit from light abrasion with emery cloth (or similar), to remove the oxide layer.

Permabond 2010 Directions for Use
1) Apply the adhesive sparingly to one surface.
2) Bring the components together quickly and correctly aligned.
3) Apply sufficient pressure to ensure the adhesive spreads into a thin film.
4) Do not disturb or re-align until sufficient strength is achieved, normally in a few seconds.
5) Any surplus adhesive can be removed with Permabond CA solvent, nitromethane or acetone.
NB:
For difficult or porous surfaces using a Permabond activator is recommended. If bonding polypropylene, polyethylene, PTFE or silicone, prime first with Permabond Polyolefin Primer (POP).

For more information download the Technical Data Sheet

Permabond_TDS_btn

Contact Us

Your information is always kept private

Products

Recent Blogs

23Mar
Permabond F201 Toughened, flexible, anaerobic sealant

Anaerobic sealants are characteristically very rigid, hard adhesives which work well in compression, torsion and shear but are notoriously brittle and unsuitable in applications where there could be peel or cleavage forces. When bonding dissi...

Read more
03Mar
FDA & EU 10/2011 Compliant Adhesive for Food Contact

PERMABOND® ET5162 is an FDA & EU 10/2011 compliant adhesive. It has been formulated to comply with both FA 175.105 and EU food contact regulations 10/2011. It is a two-part, room temperature curing epoxy adhesive, which combines high ...

Read more
14Jan
High Temperature Resistant Cyanoacrylate

Permabond introduces new high temperature resistant cyanoacrylate adhesives! PERMABOND® 825 is a low viscosity cyanoacrylate adhesive that provides higher strength at high temperature. This fast-setting cyanoacrylate bonds metals, rubbers, ...

Read more
15Dec
New no odour adhesives for low surface energy plastics

PERMABOND® is delighted to announce the launch of Permabond TA4630 and TA4631, no odour adhesives for low surface energy plastics, especially developed for difficult to bond plastics such as polypropylene, polyethylene and PTFE, witho...

Read more
18Jun
Permabond Launches UV639 High Performance Acrylic Bonder

Permabond Launches UV639 High Performance Acrylic Bonder In the world of bonding acrylic (or Perspex®, PLEXIGLASS®, PMMA as it is also known), adhesives used to join this material are often referred to as "acrylic adhesives". This shoul...

Read more
28Jun
Permabond Europe Launches TA4207 – No surface preparation!

Permabond Europe Launches TA4207 – A new versatile, high strength adhesive Permabond TA4207 expands our existing range of methyl methacrylate (MMA) adhesives, and is a 2-part, 1:1 mix ratio product, which achieves very high shear strength...

Read more