ISO QMS Certified
"Our Science ... Your Success"

Metal Bonding Acrylic Adhesives

Metal Bonding Acrylic Adhesives

Epoxies, Cyanoacrylates, and several other technologies provide excellent adhesion to metals.  Acrylic metal bonding adhesives are often chosen not only for the strong bonds to metals but also for the variety of curing options available which can optimize production processes.

Many acrylic adhesives form strong bonds to a variety of metals – often – choosing the best metal bonding acrylic adhesive, is based on the best way to apply and cure the adhesive.

Two Component Acrylic Adhesives

Many 2 part acrylic adhesives have a short pot life, said differently they begin to cure very quickly.  These are best dispensed via static mix nozzles onto one component then assembling the components quickly.  This is ideal for many high speed processes.

Some 2 part acrylic adhesives are MMA based.  Although this type can provide high bond strength to plastics, they are flammable and have a distinctive strong odor.

Permabond TA452 is a non-flammable low odor adhesive which provides up to 3,500 psi (24 N/mm2) shear strength on steel.  It has a nozzle life of 2-3 minutes and develops strength very rapidly, achieving 80% of full bond strength in 75 minutes.

Two-Part – No Mix Metal Bonding Acrylic Adhesives

Permabond TA4246  is a No-Mix adhesive which is used in conjunction with Initiator 46 to form strong bonds to metal, glass, magnets, and composites.   With no gap, TA4246 develops 80% of its strength in an hour.  Full strength on steel is over 5000 psi (35 N/mm2) TA4246 is an MMA based adhesive, so there is a distinctive odor.

If you aren’t bonding plastic, consider non-flammable TA4590 along with Initiator 44. Full strength on steel is 3600 psi (25 N/mm2).  80% of strength can be achieved in under an hour.  And handling time (0.3 N/mm2) can be achieved in under a minute.

The ability to remove parts from fixtures/jigs in under a minute can greatly improve production efficiency.

Never mix the initiator with the adhesive.

  1. Apply Initiator to one surface.
  2. Apply adhesive to the other surface.
  3. Assemble the components using sufficient force to spread the adhesive thinly. Parts should be bonded immediately and within a maximum of two hours of applying the Initiator.
  4. Maintain pressure until handling strength is achieved. The time required will vary according to the joint design, gap and surfaces being bonded.
  5. Allow 24 hours for adhesive to fully cure. Accelerated cure times may be achieved by heating.

Two-Part- Bead on Bead  Metal Bonding Acrylic Adhesives

Permabond TA440

  1. Apply TA440A to one surface and TA440B to the other.
  2. Alternatively, dispense ‘bead-on-bead’ (one bead on top of the other) and then assemble parts. NOTE: Applying adhesive side by side is not advisable as this may not achieve adequate mixing.
  3. Maintain pressure until handling strength is achieved. The time required will vary according to the joint design and surfaces being bonded.
  4. Allow 24 hours for adhesive to fully cure. Accelerated cure times may be achieved by heating.

If the above instructions aren’t clear, see the curing instruction video.

With a controlled process that provides adequate mixing of the adhesive, shear strength values on steel of 3600 psi (25 N/mm2) can be achieved.  With no gap handling time of 90 seconds or less can be achieved.

One-Part -Metal Bonding Acrylic Adhesive

Permabond TA437 can be used without initiator when bonding metals.  It is a single component structural acrylic adhesive designed primarily for bonding metals, ferrites, and ceramics. When the use of the activator is not desirable, the material will cure anaerobically in a close-fitting joint /in the presence of metal; the fixture time will be 5-10 minutes.

The typical fixture time of TA437 when used with Initiator 41 is 20-30 seconds. The fast fixture time of TA437 makes it an ideal adhesive for high-speed production lines.  This product provides high strength, tough, durable bonds with good impact resistance.

Shear strength on steel of 3000 psi (20 N/mm2) can be expected.

For assistance in choosing the best metal bonding adhesive for your application, contact Permabonds technical team.

metal bonding acrylic adhesive